Chinese|English

Planetary cycloidal-pin wheel reduction gear mated with stepless speed changer
Mode expression

 

Outline and & Installation size
Model
of
stepless speed
chan
     ger
Installation size Connection size of shaft extension end Outline size Wei
ght
Input
shaft
Output
shaft
Double
shaft
Direct connecting
type
C G E F V R n d d1 b1 c1 e1 d2 b2 c2 e2 M N H DC L L1 Lo AC AD
  100 101 90 180 45 15 4 12 ф14h6 5 16 25 ф25h6 8` 28 34 120 210 175 150 332 500 245 110 100  
02 140 151 100 250 55 20 4 16 ф14h6 5 16 30 ф35h6 10 38 55 150 290 240 200 395 570 245 110 110  
04 150 169 145 290 65 22 4 16 ф19h6 6 21.5 30 ф45h6 14 48 74 195 330 275 230 460 658 250 175 150  
07 160 206 150 370 75 25 4 18 ф24h6 8 27.3 40 ф55h6 16 59 91 260 420 356 300 575 780 290 195 160  
15 200 125 275 380 75 30 4 22 ф24h6 8 27 50 ф65h6 18 69 89 335 430 425 340 675 885 320 215 180  
Main technical parameter (Mated with cycloid reduction gear)
Model of stepless speed changer 02 04 07 15 22
KW Input power
KW
0.18 0.37 0.55 1.1 2.2
0.75 1.5 3
Input revs
r/min
1500
Model of cycloid reduction gear mated X2 X3 X4 X5 X6
Speed ratio Range of output revs
Range of output torque
    
N.m
9 21~105 24~11 46~23 77~38 139~69 277~139
93~45 186~92 372~186
11 17~86 29~14 56~28 95~47 170~85 338~170
113~56 227~113 454~227
17 11~55 44~21 86~43 146~73 263~131 523~263
175~87 351175 703~351
23 8~41 60~29 117~58 198~99 356~178 708~356
236~117 475~236 950~475
29 6~32 76~37 135~68 250~125 449~224 893~449
298~148 599~298 1199~599
35 5~27 91~44 142~71` 267~134 542~271 1078~542
319~158 723~360 1447~723
43 4~22 112~54 175~87 328~164 665~332 1324~665
392~194 889~442 1595~889

Notice for operating

    1、The machine is suitable for continuous working, and is allowed to run along with CW.

    2、When the shaft extension of output shaft and input shaft matches with other parts, please don’t hammer it directly, otherwise, it would be damaged. When the parts are connected, please make concentric installation with the help of shaft line, the installation error should not be exceed the limit value.

    3、The input revs should not be higher than stipulated value, please be slow when adjust the speed, and it is forbidden to adjust the speed when the machine stops.

    4、When it impacts load and start frequently, please set an over-load protection device between the reduction gear and working device.

    5、When the machine leaves factory, the speed-adjusting nut has already be set at the limit position, and don’t adjust it any more, otherwise, the machine may be damaged.

    6、When start with load, please start with low speed, and then adjust to the needed revs gradually.

    7、The machine adopts oil bath type lubrication, the oil height should be controlled according to the circular mark.

    8、The lubricating oil recommended for stepless speed changer as follows: oil designation: Ub-1, manufacturer: Chemical & Industrial Branch of Guanghzou Machine Tool Research Institute

    9、The gear reduction gear and planetary cycloidal-pin wheel reduction gear that connect with planetary friction type stepless speed changer adopt 40# mechanical oil or lubricating grease or reduction gear.